Basic Info.
Application
Insulators, Winding Wire Coating Insulation
Thickness
2.0mm; 2.2mm; 2.3mm; 2.5mm; 3.0mm; 3.2mm
Width
450mm or 500mm or 550mm
Construction
3lpe System or 2lpe System
Raw Material
Radiation Cross Linked PE
Working Temperature
60 Centigrade or 80 Centigrade
Type
Insulation Sleeve & Tube
Chemistry
Hybrid Insulation
Classification
Hybrid Insulation Materials
Specification
DN406*500*2.5mm
Product Description
HTLP80-HP Radiation Cross-Linked 3lpe Heat Shrinkable Sleeve for Pipes
Product description:WSS80 wraparound heat shrink sleeves is designed for corrosion protection of girth weld joint of buried and exposed steel pipes, especially for 3-layer coated oil and gas pipeline.
Construction: 3-layer PE systemFirst layer: Primer, A,B components.
Second layer: High shear strength
MASTIC copolymer adhesive.
Third layer: Radiation cross-linked, high density polyethylene backing (HDPE).
Product features/benefits:• Excellent multifunctional adhesive allows for lower installation preheat temperature and super bonding to PE, PP and FBE, offer fully resistant
to shear forces induced by soil and thermal movements.
• Superior cathodic disbondment and hot water immersion resistance offers the optimum barrier long-term protection against corrosion.
• Saves time & cost by lower preheat temperature, wet epoxy primer application.
| Product selection guide: |
| | Mastic (MWSS60) | Mastic (MWSS80) | WSS60 | WSS80 |
| Max operating temperature | 60ºC | 85ºC (185ºF) | 70ºC (158ºF) | 85ºC (185ºF) |
| Compatible line coatings | PE, FBE, PP | PE, FBE, PP | PE, FBE, PP | PE, FBE, PP |
| Min. Preheat temperature | 65ºC | 85ºC(185ºF) | 75ºC(185ºF) | 85ºC(185ºF) |
| Recommended pipe preparation | Sa2.5, St3.0 | Sa2.5, St3.0 | Sa2.5, St3.0 | Sa2.5, St3.0 |
| |
| Product properties: |
| Property | Test Method | WSS60 | WSS80 |
| Backing |
| Tensile Strength | ASTM D638 | 3000 psi (20Mpa) | 3300 psi (22.8Mpa) |
| Elongation at break | ASTM D638 | 600% | 660% |
| Design temperature | | ≥60ºC | ≥ 80°C. |
| Shrink Force | ASTM D638@150ºC (302ºF) | 35 psi | 35 psi |
| Dielectric Strength | ASTM D149 | 900 volts/mil (35kV/mm) | 900 volts/mil (35kV/mm) |
| Water Absorption | ASTM D 570 | < 0.05% (Wt) | < 0.05% (Wt) |
| Volume Resistivity | ASTM D570 | 1x 1016 Ω-cm | 1x 1016 Ω-cm |
| Adhesive |
| Softening Point | ASTM E28 | 103ºC (217ºF) | 110ºC (230ºF) |
| Lap Shear | DIN EN 12068 | 20 N/cm²@60ºC(140ºF) | 20N/cm² @80ºC(176ºF) |
| Installed Product |
| Peel Strength | DIN EN 12068 | 7N / mm | 9N / mm |
| Impact Resistance | ASTM G-14 DIN EN 12068 Class C | 75 in-lbs | 75 in-lbs |
| DIN30672 Class C | ≥15J | ≥15J |
| No holiday | No holiday |
| Indentation Resistance | DIN EN 12068 Class C | > 2.5mm @ 60ºC(140ºF) | > 3.1mm @ 80ºC(176ºF) |
| Cathodic Disbandment | DIN EN 12068 | < 15mm rad. | < 15mm rad. |
| Resistance to thermal Aging | DIN EN 12068 | After 100 days @ 100ºC | After 100 days @ 100ºC |
| -Tensile strength ratio | 0.9 | 0.9 |
| -Elongation ratio | 0.8 | 0.8 |
| Specific Coating Resistance | DIN 30672(100 days immersion) | 6*108Ω.m2 | 6*108Ω.m2 |
| Resistance to UV radiation | EN12068 | Reduction in bursting strength <25% of the original value | Reduction in bursting strength <25% of the original value |
| |
| Ordering information: |
| WSS80 products are available: • as cut piece (pre-cut sleeve with separate closure Patch • as a roll (closure patches to be ordered separately) | Range for available dimension: |
| Sleeve length for 28 inch pipe | L=π×D×1.07+120(mm), thus for 28 inch pipe, it will require 2500mm |
| Sleeve width | 450mm, 480mm, 500mm, 520mm and 550mm supplied PE shrink sleeves width. |
• Select sleeve width that will overlap onto the mill-applied coating by 2 inches (50 mm) minimum on each side of the weld joint. Take a 10% shrinkage during installation of sleeve width into account when calculating the minimum sleeve width.
• Sleeve cut lengths and appropriate closure patch widths depend on the pipe size and product construction, see application table. | Sleeve thickness | 1.8mm, 2.0mm, 2.2mm, 2.5mm, 2.8mm , 3.0mm and 3.2mm |
| Primer thickness | wet film and dry film. We can provide 120um, 150um, 200um, 300um and 400um primer thickness. |
| Service Life: More than 30 years |
| Shelf Life: 18 months, under correct storage condition |
| Normal Packing: Carton (Maximum 45kg) |
| Storage Condition: |
| To ensure maximum performance, store Dasheng products in a dry, ventilated area. |
| Keep products sealed in original cartons and avoid exposure to direct sunlight, rain, snow, dust or other adverse environmental lements. |
| Avoid prolonged storage at temperatures above 40°C or below -20°C. |
| Product installation should be done in accordance with local health and safety regulations. |
| |
Address:
Room A1010, Building 2, No. 588 Binhe Road, High Tech Zone, Suzhou, Jiangsu, China
Business Type:
Manufacturer/Factory, Trading Company
Business Range:
Construction & Decoration, Industrial Equipment & Components
Management System Certification:
ISO 9001
Company Introduction:
Our company offers variety of products which can meet your multifarious demands. We adhere to the management principles of "quality first, customer first and credit-based" since the establishment of the company and always do our best to satisfy potential needs of our customers. Our company is sincerely willing to cooperate with enterprises from all over the world in order to realize a win-win situation since the trend of economic globalization has developed with anirresistible force.
